Rhino 3d Change Drawing Plane

CPlane

The CPlane command sets the origin and orientation of the structure plane in the active viewport.

Steps

Option a new origin point or choose an option.

Command-line options

All

The construction planes in all viewports modify then their origin is at the picked location.

Bend

The Curve pick sets the construction plane perpendicular to a bend.

Curve steps

1.

Select a curve to orient construction plane.

ii.

Drag the structure plane's new x and y axes to a new location.

Note

●

Use the Bend option to apace position your construction plane at diverse stations along a fundamental track curve as training for doing a i runway sweep, for case. Once your construction plane is positioned, you can use drawing tools to depict a cross-section curve in the 3 D location where it needs to be. This directly cartoon method can be quicker and more convenient than cartoon the curve on a world airplane and then trying to motion and rotate it into place in 3-D.

●

The direction of the bend affects the management of the axes. If the structure airplane does not go the direction you want, flip the direction of the bend with the Flip or Dir commands.

Peak

The Summit option changes the height (z-direction) of the structure airplane.

Elevation steps

Pick a new elevation.

Or, type a distance to move the origin from its previous location.

Note

●

Positive numbers move the construction aeroplane upward along the positive z-axis.

●

Negative numbers move the construction airplane down.

Object

The Object option sets the construction plane in the active viewport to an object.

Object steps

Select a curve or surface.

The origin and tangency of the new construction plane is based on the "midpoint" of the untrimmed version of the surface.

Rotate

The Rotate pick rotates the construction plane.

Rotate steps

1.

Pick the offset of the rotation centrality.

2.

Pick the end of the rotation axis.

3.

Blazon the angle to rotate the construction airplane. Or, choice two points to specify the angle.

Surface

The Surface choice sets the construction plane to match a surface. The placement is constrained so that the construction plane is tangent to the surface.

Surface steps

1.

Select a surface.

2.

Pick an origin or press Enter.

iii.

Pick an ten-axis management or press Enter.

Surface options

Flip

The Flip choice reverses the management.

IgnoreTrims

The IgnoreTrims selection uses unabridged untrimmed underlying surface.

Through

The Through choice moves the construction plane origin to a selected point.

Through steps

Choice a location to motility the origin to.

Through option

All

The All option resets all construction planes to the new origin.

View

The View selection sets the construction plane in the agile viewport parallel to the view.

View steps

Click View or type V.

World

The World option restores the specified default construction plane.

Earth options

Back

Bottom

Front

Left

Correct

Summit

3Point

The 3Point pick sets the construction plane in the active viewport past specifying points to found the 10-, y-, and z-directions.

3Point steps

1.

Pick a new origin, or press Enter.

2.

Pick the 10-centrality.

3.

Pick the y-centrality.

3Point options

Vertical

The Vertical pick sets the construction airplane perpendicular to the electric current construction airplane.

ZAxis

The ZAxis option sets the construction plane z-axis direction.

Undo

The Undo option restores the previously used construction airplane in the current viewport.

Undo steps

Click Disengage or type U.

Shortcut

Shift + Home

Redo

The Redo selection restores the construction plane that was active before the Undo option was used.

Redo steps

Click Redo or type D.

Shortcut

Shift + Terminate

CopyCPlaneToAll

The CopyCPlaneToAll command changes all viewports to take the same construction planes as the specified viewport.

CopyCPlaneSettingsToAll

The CopyCPlaneSettingsToAll control changes all viewports to have the same filigree settings and snap spacing equally the specified viewport.

Encounter also

Employ construction planes

MPlane

Ready up a relationship between a construction plane and an object.

NamedCPlane

Manage the named construction planes list.

---

Rhinoceros v © 2010-2015 Robert McNeel & Associates. 17-Sep-2015

Open up topic with navigation

ingramalting56.blogspot.com

Source: http://docs.mcneel.com/rhino/5/help/en-us/commands/cplane.htm